TJA1044GTK/3Z

The TJA1044GTK/3Z is part of the Mantis family of high-speed CAN transceivers. It provides an interface between the Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus. The transceiver is specifically designed for high-speed CAN applications in the automotive industry and provides the ability to send and receive differential signals for CAN protocol controllers (in microcontrollers).

Main applications: industrial control, automotive electronics

MM74HCT14MX

The MM74HCT14MX uses advanced silicon gate CMOS technology with the low power consumption and high immunity characteristics of standard CMOS and can drive up to 10 LS-TTL loads. 74HC logic family is compatible with the standard 74LS logic family in terms of functionality and pin arrangement. Protects all inputs from damage due to electrostatic discharge from internal diode clamping to VCC and ground.

Main applications: Suitable for a wide range of applications

LMV358IDRG4Q1

The LMV358IDRG4Q1 are dual low voltage (2.7 V to 5.5 V) operational amplifiers with rail-to-rail output swing. These devices are the most cost effective solution for applications requiring low voltage operation, space saving and low cost.

Key applications: Suitable for a wide range of applications

AD6641BCPZRL7-500

The AD6641BCPZRL7-500 is a 250 MHz bandwidth digital pre-distortion (DPD) observation receiver with an integrated 12-bit 500 MSPS ADC, a 16k × 12 FIFO and a multi-mode back-end that allows the user to retrieve the data stored in the integrated FIFO via the serial port (SPORT), SPI interface, 12-bit parallel CMOS port or 6-bit DDR LVDS port. Retrieve data stored in the integrated FIFO memory. It offers excellent dynamic performance and low power consumption for telecom applications such as digital pre-distortion observation paths requiring wider bandwidths. All the necessary functions are integrated on the chip, including a sample-hold and reference voltage source, to provide a complete signal conversion solution.

Key applications: wireless and wired broadband communications, communications test equipment, power amplifier linearisation

TL062IDT

The TL062IDT is a low input current (200pA) low power (200uA) 36V JFET dual op-amp. These JFET input op amps incorporate well matched high voltage JFETs and bipolar transistors in a monolithic IC. They offer high conversion rates, low input bias and detuning currents and low detuning voltage temperature coefficients.

Main applications: Suitable for a wide range of applications  

BFP420E6327

The BFP420E6327 is an NPN silicon RF transistor for use in high gain low noise amplifiers. Suitable for oscillators up to 10 Ghz, noise figure F = 1.1 dB at 1.8 Ghz, conversion frequency fT = 25 GHz, high reliability gold plated layer, SIEGET® 25 GHz fT - line, lead-free, (RoHS) compliant package, certification report according to AEC-Q101.

Main applications: wireless communications, RF front-end active mixer, amplifier and oscillator applications

AGQ200A24

The AGQ200A24 is a high sensitivity, 100 mW nominal operating power, 2 C type compact flat body relay.

Main applications: Telephone switchboards, telecom equipment, security, measurement equipment, consumer electronics and audio and visual equipment

STM32F401CBU7

The STM32F401CBU7 is a high-performance basic series Arm® Cortex®-M4 microcontroller with DSP and FPU, featuring 128 KB Flash, 84 MHz CPU and ART accelerator. All devices offer a 12-bit ADC, a low power RTC, six general purpose 16-bit timers (including a PWM timer for motor control) and two general purpose 32-bit timers. They also feature standard and advanced communication interfaces.

Main applications: Suitable for a wide range of applications

ZXTN2010ZTA

The ZXTN2010ZTA is an NPN, 60V, 5A transistor. This new low saturation 60V NPN transistor in SOT89 package has extremely low state losses and is ideally suited for DC-DC circuits as well as various drive and power management functions.

Key applications: emergency lighting circuits, motor drives (including DC fans), backlight inverters, power switches, gate drive MOSFETs and IGBTs

74HC4067DB,118

The 74HC4067DB,118 is a single-blade 16-throw analogue switch (SP16T). It is suitable for analogue or digital 16:1 multiplexer/demultiplexer applications. The switch has four digital select inputs (S0, S1, S2 and S3), sixteen independent inputs/outputs (Yn), a common input/output (Z) and a digital enable input. When the digital enable input is high, the switch is closed. The inputs include clamp diodes. This allows the input to be connected to a voltage exceeding VCC using a current limiting resistor.

Main applications: analogue multiplexing and demultiplexing, digital multiplexing and demultiplexing, signal gating

What other chips do you usually use

but are not on the list?